What Size Punch For Ruger 10 22

Ruger'due south x/22 is likely the single most popular rifle action in contest across the multitude of .22 LR disciplines, particularly among those that require rapid burn in a diverseness of positions. A few inexpensive maintenance tools specific to the ten/22 significantly ease disassembly and reassembly—and preclude lost springs, plungers and tempers.

Ruger 10/22 tools

The Gunsmither Rubber Tool and 10/22 Commodities Bar and Extractor Tool from Tandemkross tin relieve frustration and lost parts.

Semi-automatics used in competitive shooting can get dingy—actually dirty—and they need frequent disassembly for cleaning to keep them operating reliably. Though the Ruger 10/22 is 1 of the simplest semi-automatic rimfire rifles to field strip, information technology does have a few pattern foibles that seem to require a third hand or esoteric knowledge to get it apart and back together again. And, as with whatsoever firearm, springs and plungers tin fly out and disappear when using an inadequate tool, rendering the firearm unusable until replacement parts go far—parts that may also fly off and disappear to join their brethren. Permit'due south look at a couple of tools offered by .22 LR accessories guru Tandemkross that help brand taking apart and reassembling the Ruger 10/22 a whole lot less frustrating.

Spring Compressors

Showtime up is a device so simple that the maker evidently decided it should do more merely i job. The Gunsmither 10/22 Bolt Bar and Extractor Tool is a piece of bent aluminum bar used to ease reinstallation of the commodities by depressing the bolt handle and spring associates and holding information technology in place until yous can drop the bolt back in.

10/22 Bolt Bar & Extractor Tool

The 10/22 Bolt Bar and Extractor Tool makes installing the bolt much easier.

To employ, invert the receiver as usual when reassembling, drop in the bolt handle and spring assembly, depress the spring with the Bolt Bar tool, drib the bolt into place at the rear, push down firmly on the bolt and slowly withdraw the tool. The bolt handle will snap into its recess in the bolt. Because the tool is aluminum, it won't gouge the aluminum 10/22 receiver.

Job number two of the tool is to aid remove and reinstall the 10/22'due south extractor without losing the spring and plunger. There are two pins on the edge of the tool; insert the front pin between the extractor and plunger face, pull back against the extractor spring and lock the other pin against the dorsum of the commodities. The tool keeps the bound compressed while you remove the extractor and and then ease pressure off the spring to remove spring and plunger. Use information technology the same way to reinstall the spring, plunger and extractor.

10/22 Bolt Bar and Extractor Tool | Tandemkross

In addition, the 10/22 Commodities Bar and Extractor Tool keeps the ejector jump and plunger convict during removal and installation.

Third Hand

It usually isn't necessary to break downwards the 10/22 trigger assembly for routine cleaning; oft, a spray cleaner followed by a few drops of lubricant will suffice for years. But the high volume of cartridges fired through a competition 10/22, coupled with the requirement for flawless reliability and consequent trigger pull, necessitates occasional detail stripping and cleaning of the trigger guard assembly.

Gunsmither Safety Tool

The Condom Tool is a double-headed drift punch, condom spring and plunger servant, and disconnector slave pin.

Near folks hesitate to mess with taking apart any trigger assembly, often because of by bad experience. Even so, the 10/22'south trigger guard associates is comparatively unproblematic, once you know a slave pin is a necessary "third hand" to ease its reassembly.

Ruger 10/22 maintenance

Push the safety button out, and so rotate the tool to release the spring and plunger.

Tandemkross's Gunsmither Condom Tool is actually iii separate tools that assist in retaining the spring and plunger when removing and reinstalling the 10/22 safety button, to remove and reinstall the trigger baby-sit pins, and remove/reinstall the disconnector pin. The latter is where the Safety Tool's slave pin comes in, and it will improve your quality of life in avoiding bafflement and frustration when reassembling the unit of measurement. Like the Commodities Bar and Extractor Tool, the Safe Tool actually works and makes working with the Ruger's trigger guard assembly a whole lot easier.

Using the Ruger 10/22 Gunsmither Safety Tool

Use the Safety Tool to drift the pins in and out of the trigger guard associates.

Gunsmither Tools is the maker of these unique 10/22 tools, but you'll save xx to 25 per centum when you purchase them from Tandemkross instead. That may seem odd, but that'southward capitalism. Detailed written instructions accompany the tools; Gunsmither Tools' illustrations are hand-drawn but usable. For Millennials, video instructions are available at the Tandemkross website.

If you lot put a lot of rounds through your competition ten/22, or fifty-fifty weekend bricks through your plinker 10/22, at $12.95 for the Bolt Bar and Extractor Tool and $fourteen.99 for the Rubber Tool, these inexpensive accessories will save yous some frustration while maintaining your 10/22 in top condition.

Meet more: Review: Ruger Custom Shop 10/22 Rifles